Home / Service areas / Miami-Dade County / Opa-locka
Miami-Dade County · Florida
Opa-locka dry ice blasting
Opa-locka work comes to us the same way most of it does: something is coated in build-up and cannot be sanded, soaked or dissolved.
What a job looks like locally
The compressor runs off the truck, so there is no wash pad to find and no runoff to manage. That is the practical reason a mobile rig beats hauling equipment somewhere: the machine never leaves Opa-locka.
Dry ice sublimates on contact, so there is no grit, no slurry and no secondary media to sweep up afterward. What is left on the floor is the grease or carbon that came off, and collecting that is part of the job.
What we clean
What we clean in and around Opa-locka
Nearby
Also working across Miami-Dade County
Questions from Opa-locka
Will you work during a shutdown?
Most of the time. Shutdowns and after-hours work are normal for us; what matters is knowing the window early.
What kinds of jobs do you take here?
It ranges from a single restoration project to a plant maintenance window. The method does not change much.
Do you charge for the drive?
It depends how far out the job is. We will be straight with you about it when you describe the work.
How do I get started?
Describe the job and send a photo or two. Giancarlo or Kenny will call you, not a scheduler.
Do you cover Opa-locka?
Yes. Opa-locka is inside our regular working area, and the rig travels to the job rather than the other way round.
What do we have to provide?
Access to the equipment and somewhere to park the compressor. No water hookup, no drain and no wash bay.
Conditions around Opa-locka
The heat matters more than people expect: baked-on residue cures harder in a South Florida summer. That is why so much of the work is removing what has bonded to a surface without taking the surface with it.
Light industrial, automotive and marine make up most of what we are called out for. Whatever the setting, the rig arrives with its own compressor and containment, so nothing about the site has to change to accommodate us.
No runoff and no residual grit, which matters more than it sounds on a Miami-Dade County job with neighbors close by.
What comes off
What this takes off
The method does not care much what the contaminant is, only that it sits on top of something. Here is the usual list.
- Paint and coatings
Taken off in a controlled way when what is underneath matters more than speed.
- Salt and corrosion product
Salt deposit and the oxidation it starts. Anything abrasive removes the protection along with the salt.
- Ink and printing residue
Dried ink on precision roller faces, cleaned without altering the cell structure that does the work.
- Food residue
Burnt-on product, fat and sugar on processing gear, with no chemical residue left on a contact surface.
- Grease and oil
The soft film that holds dust and swarf against metal. It is what makes a part feel dirty long after it looks clean, and it comes off first.
- Carbon and soot
Heat-bonded black deposit. Because heat put it there, a sudden cold front is what breaks its grip.
- Adhesive and sealant
Sealant squeezed out and cured where it was never supposed to set.
How a job runs
The sequence, start to finish
There is no mystery to how these jobs run, and no part of it we would rather you did not ask about.
- You describe the job
Tell us the machine, the mess and the constraint. A couple of photos answers more than a long description, and if the honest answer is that something else suits it better, we say so.
- We look at access and containment
Siting the compressor, masking what must not be touched, and catching what comes off, settled before the first pellet.
- We test a small area
Pressure and pellet size get dialed in on an inconspicuous spot before we touch anything visible. Painted parts, soft alloys and older finishes all behave differently, and the right setting on one is the wrong setting on another.
- We blast, then clean up
One mess instead of two: the pellet vanishes and we take away what it removed.
- You look before we pack up
We would rather you find the missed spot while we are standing there than a week later. Another pass on the day is the cheapest fix available.
The comparison
How this compares to the usual methods
- Media blasting
Cuts into the substrate by design. Fine on structural steel, wrong on aluminum, plating, machined faces or anything with a tolerance.
- Pressure washing
Forces water where water should not go, looms, bearings, seams, and then the job stops while it dries.
- Solvent and degreaser
It loosens the mess and leaves its own behind, along with fumes and something to dispose of.
- Hand scraping
Hours of work for an inconsistent result, with gouges where the blade slipped.
- Dry ice
Thermal contraction cracks the bond between deposit and surface, then the pellet gasses off. Nothing abrasive, nothing wet, nothing left.
Before we turn the rig on
This is not a quiet method. Ear defenders are standard issue on site for anyone nearby.
The part will be cold when we finish. Sometimes that means a short wait before handling; sometimes it means a film of condensation as it warms back up.
Air comes from our own compressor. You do not need to provide power, water or a connection of any kind.
We cover what should not be hit before anything gets blasted. It takes minutes and saves arguments.
Send us the job.
Give us the job, the address and a rough description, pictures if you have them. The call back comes from Giancarlo or Kenny directly.