Home / Service areas / Palm Beach County / Jupiter Inlet Colony
Palm Beach County · Florida
Jupiter Inlet Colony dry ice blasting
Jupiter Inlet Colony calls tend to arrive with a constraint attached, which is exactly where this method earns its keep.
How we work in this area
The compressor runs off the truck, so there is no wash pad to find and no runoff to manage. So the equipment stays put. Everything that has to move arrives on the truck instead.
The pellet turns straight to gas when it hits, which means no sand in the machine and no sludge on the floor. The only thing to collect is the contaminant itself, and that is included.
What we clean
What we get called for in Jupiter Inlet Colony
Nearby
Also working across Palm Beach County
Questions from Jupiter Inlet Colony
Will you work during a shutdown?
Usually. Tell us the window you have, including overnight or a planned shutdown, and we will tell you honestly what fits in it.
What kinds of jobs do you take here?
A mix, vehicle work, shop equipment, marine and light industrial. Same rig, different constraint each time.
Do you charge for the drive?
It depends how far out the job is. We will be straight with you about it when you describe the work.
How do I get started?
A short description and a couple of pictures is enough to start. An owner rings you back.
Do you cover Jupiter Inlet Colony?
Yes. Jupiter Inlet Colony is inside our regular working area, and the rig travels to the job rather than the other way round.
What do we have to provide?
Just access and parking. There is no tap to find, no drain to use and nothing of yours to plug into.
Conditions around Jupiter Inlet Colony
Afternoon storms mean equipment that lives outside is wet, then hot, then wet again. It is also why an abrasive method costs you twice: once in the cleaning, again in the finish you removed.
Residential garages and small shops sit alongside the commercial work on any given week. In every case the truck brings its own air and its own containment, so you are not adapting the site to suit the method.
The pellet turns to gas, so nothing runs off toward a drain and nothing abrasive stays behind in a bearing. On a cramped Palm Beach County site that usually decides it.
What comes off
What dry ice actually removes
The rule of thumb is simple: anything stuck on rather than built in. These are the deposits we see most.
- Paint and coatings
Taken off in a controlled way when what is underneath matters more than speed.
- Salt and corrosion product
Salt deposit and the oxidation it starts. Anything abrasive removes the protection along with the salt.
- Ink and printing residue
Dried ink on precision roller faces, cleaned without altering the cell structure that does the work.
- Food residue
Carbonized product build-up in a plant where neither standing water nor a chemical film is acceptable.
- Grease and oil
Degreasers leave their own residue behind. Dry ice takes the oil off without adding anything, so there is no chemical left on the part afterward.
- Carbon and soot
The dark scale on ovens and exhaust parts. Of everything we remove, this is often the quickest to release, because the bond is a heat bond.
- Adhesive and sealant
Sealant squeezed out and cured where it was never supposed to set.
How a job runs
How a job actually runs
If this is your first time hiring dry ice blasting, the steps below are what to expect. Nothing happens on the day that we have not talked through.
- We test a small area
No two jobs run at the same numbers. A quiet corner of the part is where we settle pressure and pellet size for this one.
- We blast, then clean up
The media disappears on contact; the contaminant does not. Gathering what came off is included, not a line added afterward.
- You look before we pack up
Walk it with us before the hose goes away. A second pass while the compressor is still running costs nothing; a return visit costs us both.
- You describe the job
Describe the equipment and the mess. If it cannot come offline that changes the plan, so say so early.
- We look at access and containment
Hose run, compressor position, what needs masking, and where the contaminant is collected. For food and electrical jobs the containment plan takes longer to settle than the blasting does.
The comparison
How this compares to the usual methods
- Media blasting
It takes the top off whatever it touches. That is the point on rusted plate and the problem everywhere else.
- Pressure washing
Water gets into everything and has to come out again before the equipment runs. Around electrics it is off the table entirely.
- Solvent and degreaser
Softens the contaminant but leaves a film, fumes and a disposal problem, and attacks finishes you meant to keep.
- Hand scraping
Hours of work for an inconsistent result, with gouges where the blade slipped.
- Dry ice
It is the only one on this list where the media stops existing the moment it has worked.
What the job is like to stand next to
A part that just came clean will be chilly for a few minutes. Let it warm before you coat, polish or apply anything to it.
A driveway works as well as a plant floor. Everything the job needs, air included, arrives with us.
Masking happens first. Whatever is adjacent and vulnerable gets covered before the hose is picked up.
Outdoors there is nothing to manage. Inside a closed room, the CO2 coming off the pellets displaces oxygen even though it is non-toxic and leaves no trace. That is why airflow is planned before we begin.
Describe what you are dealing with.
Tell us what you have and where it is. If you can snap a picture, send it. Giancarlo or Kenny will be the one who calls.