Home / Service areas / Palm Beach County / Royal Palm Beach
Palm Beach County · Florida
Royal Palm Beach dry ice blasting
Most of what we clean around Royal Palm Beach is equipment somebody cannot afford to damage.
How we work in this area
The compressor runs off the truck, so there is no wash pad to find and no runoff to manage. So the equipment stays put. Everything that has to move arrives on the truck instead.
The pellet turns straight to gas when it hits, which means no sand in the machine and no sludge on the floor. The only thing to collect is the contaminant itself, and that is included.
What we clean
What we get called for in Royal Palm Beach
Nearby
Also working across Palm Beach County
Questions from Royal Palm Beach
Do you cover Royal Palm Beach?
We do. The whole point of a mobile setup is that Royal Palm Beach is no further than any other stop on the schedule.
What do we have to provide?
Space for the rig and a way to reach the machine. Everything else arrives with us.
Will you work during a shutdown?
Nearly always. Give us the hours you can spare and we will say what genuinely fits inside them.
What kinds of jobs do you take here?
A mix, vehicle work, shop equipment, marine and light industrial. Same rig, different constraint each time.
Does distance affect the price?
Sometimes, on the longer runs. Either way it is discussed before anyone commits.
What is the first step?
Send the equipment, the location and a short description with photos if you have them. One of the owners calls you back.
Conditions around Royal Palm Beach
Afternoon storms mean equipment that lives outside is wet, then hot, then wet again. It is also why an abrasive method costs you twice: once in the cleaning, again in the finish you removed.
Residential garages and small shops sit alongside the commercial work on any given week. The setup is the same in all of them, because everything the job needs turns up on the van.
The pellet turns to gas, so nothing runs off toward a drain and nothing abrasive stays behind in a bearing. On a cramped Palm Beach County site that usually decides it.
What comes off
What dry ice actually removes
The rule of thumb is simple: anything stuck on rather than built in. These are the deposits we see most.
- Ink and printing residue
Ink and coating on anilox and press rollers, surfaces where changing the texture changes the print.
- Food residue
Burnt-on product, fat and sugar on processing gear, with no chemical residue left on a contact surface.
- Grease and oil
Where heat is involved the grease cooks on and hardens. The cold breaks its bond and the film lifts away without soap or solvent.
- Carbon and soot
Heat-bonded black deposit. Because heat put it there, a sudden cold front is what breaks its grip.
- Adhesive and sealant
Whatever the last repair left stuck to the mating face: gasket, sealant, deadener or adhesive.
- Resin and mold release
Release agent and resin build-up on tooling, where a solvent fix trades one residue for another.
- Paint and coatings
Removed selectively where the substrate underneath has to survive, which rules out most abrasive approaches.
How a job runs
How a job actually runs
Here is how a typical job goes, from the first call to the cleanup. We would rather you know it all before booking.
- You describe the job
Tell us the machine, the mess and the constraint. A couple of photos answers more than a long description, and if the honest answer is that something else suits it better, we say so.
- We look at access and containment
Tight sites need a plan for where people walk. We mark out a working zone so staff and visitors stay clear while the hose is live.
- We test a small area
A test spot takes minutes and protects the whole job. It tells us how hard to push on this particular surface, which matters more than any rule of thumb.
- We blast, then clean up
One mess instead of two: the pellet vanishes and we take away what it removed.
- You look before we pack up
Walk it with us before the hose goes away. A second pass while the compressor is still running costs nothing; a return visit costs us both.
The comparison
How this compares to the usual methods
- Solvent and degreaser
Trades the deposit for a residue, plus ventilation and waste to deal with, and it is hard on the finish.
- Hand scraping
Hours of work for an inconsistent result, with gouges where the blade slipped.
- Media blasting
Cuts into the substrate by design. Fine on structural steel, wrong on aluminum, plating, machined faces or anything with a tolerance.
- Pressure washing
Forces water where water should not go, looms, bearings, seams, and then the job stops while it dries.
- Dry ice
Thermal shock breaks the bond. The pellet sublimates, so nothing abrasive touches the part and nothing is left to collect but the contaminant.
What the job is like to stand next to
Dry ice is plain carbon dioxide. It is not toxic and leaves nothing behind, but in a closed room it crowds out oxygen, so we sort out airflow before we start.
Expect noise. Everybody inside the working area wears hearing protection, us included.
The surface ends up colder than the room around it. That is the only thing the process leaves, and it goes away by itself.
There is nothing to connect on your end. The truck carries what the blaster needs, so setup is quick once we are parked.
Describe what you are dealing with.
The quickest way in is a short description, a location and a photo. The reply comes from an owner, either Giancarlo or Kenny.